View M4T28-BR12SH1_8946568.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

january 2009 rev 6 1/41 1 m41t94 serial real-time clock with 44 bytes nvram and reset features counters for tenths/hundredths of seconds, seconds, minutes, hours, day, date, month, year, and century 32 khz crystal oscilla tor integrating load capacitance (12.5 pf) providing exceptional oscillator stability and high crystal series resistance operation serial peripheral interface (2 mhz spi) ultralow battery supply current of 500 na (max) 2.7 to 5.5 v operating voltage 2.5 to 5.5 v oscillato r operating voltage battery low flag automatic switchover and deselect circuitry 44 bytes of general purpose ram programmable alarm and interrupt function (valid even during battery backup mode) accurate programmable watchdog timer (from 62.5 ms to 128 s) microprocessor po wer-on reset choice of power-fail deselect voltages (v cc = 2.7 to 5.5 v): ?ths = v ss ; 2.55 v v pfd 2.70 v ?ths = v cc ; 4.20 v v pfd 4.50 v packaging includes a 28-lead soic and snaphat ? top (to be ordered separately) or 16-lead soic 28-lead soic package provides direct connection for a snaphat ? top which contains the battery and crystal rohs compliant ? lead-free second level interconnect 28 1 16 1 so16 (mq) soh28 (mh) snaphat ? (sh) battery & crystal www.st.com
contents m41t94 2/41 contents 1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.1 serial data output (sdo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2 serial data input (sdi) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.3 serial clock (scl) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.4 chip enable (e ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 spi bus characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.2 read and write cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.3 data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.1 power-down time-stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.2 clock registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.3 setting alarm clock registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.4 watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.5 square wave output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.6 power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.7 reset inputs (rstin1 & rstin2 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.8 calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.9 century bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.10 output driver pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.11 battery low warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.12 t rec bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.13 initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6 dc and ac parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
m41t94 contents 3/41 8 part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 9 environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 10 references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 11 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
list of figures m41t94 4/41 list of figures figure 1. logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 2. 16-pin soic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 3. 28-pin soic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 figure 4. block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 figure 5. hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 figure 6. data and clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 figure 7. input timing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 8. output timing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 9. read mode sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 10. write mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 11. alarm interrupt reset waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 figure 12. backup mode alarm waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 13. rstin1 and rstin2 timing waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 figure 14. crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 figure 15. calibration waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 figure 16. ac testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 figure 17. power down/up mode ac waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 figure 18. so16 ? 16-lead plastic small outline package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 figure 19. soh28 ? 28-lead plastic small outline, battery snaphat ? , package outline . . . . . . . . . . 34 figure 20. sh ? 4-pin snaphat ? housing for 48 mah battery & crystal, package outline. . . . . . . . . 35 figure 21. sh ? 4-pin snaphat ? housing for 120 mah battery & crystal, package outline. . . . . . . . 36 figure 22. recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
m41t94 list of tables 5/41 list of tables table 1. signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 2. function table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 3. ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 table 4. clock register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 5. alarm repeat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 6. square wave output frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 table 7. reset ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 8. t rec definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 9. default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 10. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 11. dc and ac measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 12. capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 13. dc characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 14. crystal electrical characteristics (externally supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 15. power down/up ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 16. so16 ? 16-lead plastic small outline package mechanical data. . . . . . . . . . . . . . . . . . . . . 33 table 17. soh28 ? 28-lead plastic small outline, battery snaphat ? , package mechanical data . . 34 table 18. sh ? 4-pin snaphat ? housing for 48 mah battery & crystal, package mechanical data . 35 table 19. sh ? 4-pin snaphat ? housing for 120 mah battery & crystal, package mech. data . . . . 36 table 20. ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 table 21. snaphat ? battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 table 22. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
description m41t94 6/41 1 description the m41t94 is a serial real-time clock with 44 bytes of nvram and a reset output. a built-in 32,768 hz oscillator (external crystal controlled) and 8 bytes of the sram (see table 4 on page 18 ) are used for the clock/calendar function and are configured in binary coded decimal (bcd) format. an additional 12 bytes of ram provide status/control of alarm, watchdog and square wave functions. addresses and data are transferred serially via a serial spi interface. the built-in address register is incremented automatically after each write or read data byte. the m41t94 has a built-in power sense circuit which detects power failures and automatically switches to the battery supply when a power failure occurs. the energy needed to sustain the sram and clock operations can be supplied by a small lithium button-cell supply when a power failure occurs. functions available to the user include a non-volatile, time-of-day clock/calendar, alarm interrupts, watchdog timer and programmable square wave output. other features include a power-on reset as well as two additional debounced inputs (rstin1 and rstin2 ) which can also generate an output reset (rst ). the eight clock address locations contain the century, year, month, date, day, hour, minute, second and tenths/hundredths of a second in 24-hour bcd format. corrections for 28, 29 (leap year - valid until year 2100), 30 and 31 day months are made automatically. the ninth clock address location controls user access to the clock information and also stores the clock software calibration setting. the m41t94 is supplied in either a 16-lead plas tic soic (requiring user supplied crystal and battery) or a 28-lead soic snaphat ? package (which integrates both crystal and battery in a single snaphat top). the 28-pin, 330 mil soic provides sockets with gold plated contacts at both ends for direct connection to a separate snaphat housing containing the battery and crystal. the unique design allows the snaphat battery/crystal package to be mounted on top of the soic package after the completion of the surface mount process. insertion of the snaphat housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surface-mounting. the snaphat housing is also keyed to prevent reverse insertion. the soic and battery/crystal packages are shipped separately in plastic anti-static tubes or in tape & reel form. for the 28-lead soic, the battery/crystal package (e.g., snaphat) part number is ?m4txx-br12sh? (see table 21 on page 37 ). caution: do not place the snaphat batt ery/crystal top in conductive foam, as this will drain the lithium button-cell battery.
m41t94 description 7/41 figure 1. logic diagram 1. for so16 package only. figure 2. 16-pin soic connections ai03683 scl v cc m41t94 v ss e rstin1 irq/ft/out sqw wdi ths rst sdo v bat (1) xi (1) xo (1) sdi rstin2 ai03684 8 2 3 4 5 6 7 9 10 11 12 13 14 16 15 1 rstin1 wdi irq/ft/out sdo v bat sdi e sqw scl ths rstin2 v ss rst xo xi v cc m41t94
description m41t94 8/41 figure 3. 28-pin soic connections table 1. signal names e chip enable irq /ft/out interrupt/frequency test/out output (open drain) rst reset output (open drain) rstin1 reset 1 input rstin2 reset 2 input scl serial clock input sdi serial data input sdo serial data output sqw square wave output ths threshold select pin wdi watchdog input xi (1) 1. for so16 package only. oscillator input xo (1) oscillator output v bat (1) battery supply voltage v cc supply voltage v ss ground ai03685 8 2 3 4 5 6 7 9 10 11 12 13 14 22 21 20 19 18 17 16 15 28 27 26 25 24 23 1 rstin1 nc nc nc nc wdi nc nc irq/ft/out nc nc nc ths nc scl sdi nc v ss sdo rst nc sqw v cc m41t94 nc nc e rstin2 nc
m41t94 description 9/41 figure 4. block diagram 1. open drain output figure 5. hardware hookup 1. cpol (clock polarity) and cpha (clock phase) are bits that may be set in the spi control register of the mcu. ai04785 compare v pfd = 4.4v v cc compare v so = 2.5v v bl = 2.5v bl compare crystal spi interface real time clock calendar 44 bytes user ram rtc w/alarm & calibration watchdog square wave sdo e sdi scl rstin1 por sqw rst (1) wdi wdf af irq/ft/out (1) v bat 32khz oscillator rstin2 (2.65v if ths = v ss ) ai03686 master (st6, st7, st9, st10, others) spi interface with (cpol, cpha) (1) = ('0','0') or ('1','1') d q c cs3 cs2 cs1 m41t94 e xxxxx cqd xxxxx cqd e e cqd
description m41t94 10/41 figure 6. data and clock timing table 2. function table mode e scl sdi sdo disable reset h input disabled input disabled high z write l data bit latch high z read l x next data bit shift (1) 1. sdo remains at high z until eight bits of data are ready to be shifted out during a read. ai04630 ai04631 ai04632 c c msb lsb cpha sdi 0 1 cpol 0 1 msb lsb sdo
m41t94 signal description 11/41 2 signal description 2.1 serial data output (sdo) the output pin is used to transfer data serially out of the memory. data is shifted out on the falling edge of the serial clock. 2.2 serial data input (sdi) the input pin is used to transfer data serially into the device. instructions, addresses, and the data to be written, are each received this way. input is latched on the rising edge of the serial clock. 2.3 serial clock (scl) the serial clock provides the timing for the serial interface (as shown in figure 7 on page 13 and figure 8 on page 14 ). the w/r bit, addresses, or data are latched, from the input pin, on the rising edge of the clock input. the output data on the sdo pin changes state after the falling edge of th e clock input. the m41t94 can be driven by a microcontroller with its spi peripheral running in either of the two following modes: (cpol, cpha) = ('0', '0') or (cpol, cpha) = ('1', '1'). for these two modes, input data (sdi) is latched in by the low-to-high transition of clock scl, and output data (sdo) is shifted out on the high-to-low transition of scl (see ta bl e 2 on page 10 and figure 6 on page 10 ). 2.4 chip enable (e ) when e is high, the memory device is deselected, and the sdo output pin is held in its high impedance state. after power-on, a high-to-low transition on e is required prior to the start of any operation.
operation m41t94 12/41 3 operation the m41t94 clock operates as a slave device on the spi serial bus. each memory device is accessed by a simple serial interface that is spi bus compatible. the bus signals are scl, sdi and sdo (see table 1 on page 8 and figure 5 on page 9 ). the device is selected when the chip enable input (e ) is held low. all instructions, addr esses and data are shifted serially in and out of the chip. the most significant bit is presented first, with the data input (sdi) sampled on the first rising edge of the clock (scl) after the chip enable (e ) goes low. the 64 bytes contained in the device can then be accessed sequentially in the following order: 1 st byte: tenths/hundredths of a second register 2 nd byte: seconds register 3 rd byte: minutes register 4 th byte: century/hours register 5 th byte: day register 6 th byte: date register 7 th byte: month register 8 th byte: year register 9 th byte: control register 10 th byte: watchdog register 11 th - 16 th bytes: alarm registers 17 th - 19 th bytes: reserved 20 th byte: square wave register 21 st - 64 th bytes: user ram the m41t94 clock continually monitors v cc for an out-of tolerance condition. should v cc fall below v pfd , the device terminates an access in progress and resets the device address counter. inputs to the device will not be recognized at th is time to prevent erroneous data from being written to the device from a an out-of-tolerance system. when v cc falls below v so , the device automatically switches over to the battery and powers down into an ultra low current mode of operation to conserve battery life. as system power returns and v cc rises above v so , the battery is disconnected, and the power supply is switched to external v cc . write protection continues until v cc reaches v pfd (min) plus t rec (min). for more information on battery storage life refer to application note an1012.
m41t94 operation 13/41 3.1 spi bus characteristics the serial peripheral interface (spi) bus is intended for synchronous communication between different ics. it consists of four signal lines: serial data input (sdi), serial data output (sdo), serial clock (scl) and a chip enable (e ). by definition a device that gives out a message is called ?transmitter,? the receiving device that gets the message is called ?receiver.? th e device that controls the message is called ?master.? the devices that are controlled by the master are called ?slaves.? the e input is used to initiate and terminate a data transfer. the scl input is used to synchronize data transfer between the master (micro) and the slave (m41t94) devices. the scl input, which is generated by the microcontroller, is active only during address and data transfer to any device on the spi bus (see figure 5 on page 9 ). the m41t94 can be driven by a microcontroller with its spi peripheral running in either of the two following modes: (cpol, cpha) = ('0', '0') or (cpol, cpha) = ('1', '1'). for these two modes, input data (sdi) is latched in by the low-to-high transition of clock scl, and output data (sdo) is shifted out on the high-to-low transition of scl (see ta bl e 2 on page 10 and figure 6 on page 10 ). there is one clock for each bit transferred. address and data bits are transferred in groups of eight bits. due to memory size the second most significant address bit is a don?t care (address bit 6). figure 7. input timing requirements ai04633 scl sdi e msb in sdo tdvch high impedance lsb in telch tchdx tdldh tdhdl tchcl tclch tehch tehel tcheh
operation m41t94 14/41 figure 8. output timing requirements ai04634 scl sdo e lsb out sdi addr. lsb in tehqz tch tcl tqlqh tqhql tclqx tclqv msb out table 3. ac characteristics symbol parameter (1) min max unit f scl serial clock input frequency dc 2 mhz t ch (2) clock high 200 ns t chcl (3) clock transition (fall time) 1 s t chdx serial clock input high to input data transition 50 ns t cheh serial clock input high to chip enable high 200 ns t cl (2) clock low 200 ns t clch (3) clock transition (rise time) 1 s t clqv serial clock input low to output valid 150 ns t clqx serial clock input low to output data transition 0 ns t dhdl (3) input data transition (fall time) 1 s t dldh (3) input data transition (rise time) 1 s t dvch input data to serial clock input high 40 ns t ehch chip enable high to serial clock input high 200 ns t ehel chip enable high to chip enable low 200 ns t ehqz (3) chip enable high to output high-z 250 ns t elch chip enable low to serial clock input high 200 ns t qhql (3) output data transition (fall time) 100 ns t qlqh (3) output data transition (rise time) 100 ns 1. valid for ambient operating temperature: t a = ?40 to 85c; v cc = 2.7 to 5.5 v (except where noted). 2. t ch + t cl 1/f scl 3. value guaranteed by design, not 100% tested in production.
m41t94 operation 15/41 3.2 read and write cycles address and data are shifted msb first into the serial data input (sdi) and out of the serial data output (sdo). any data transfer considers the first bit to define whether a read or write will occur. this is followed by seven bits defining the address to be read or written. data is transferred out of the sdo for a read operation and into the sdi for a write operation. the address is always the second through the eighth bit written after the enable (e ) pin goes low. if the first bit is a '1,' one or more write cycles will occur. if the first bit is a '0,' one or more read cycles will occur (see figure figure 9 on page 16 and figure 10 on page 16 ). data transfers can occur one byte at a time or in multiple byte burst mode, during which the address pointer will be automatica lly incremented. for a single byte transfer, one byte is read or written and then e is driven high. for a multiple byte transfer all that is required is that e continue to remain low. under this condit ion, the address pointer will continue to increment as stated previously . incrementing will continue until the device is deselected by taking e high. the address will wrap to 00h after incrementing to 3fh. the system-to-user transfer of clock data will be halted whenever the address being read is a clock address (00h to 07h). although the clock continues to maintain the correct time, this will prevent updates of time and date during either a r ead or write of these address locations by the user. the update will resume eith er due to a deselect co ndition or when the pointer increments to an non-clock or ram address (08h to 3fh). note: this is true both in read and write mode. 3.3 data retention mode with valid v cc applied, the m41t94 can be accessed as described above with read or write cycles. should the suppl y voltage decay, the m41t94 will automatically deselect, write protecting itself when v cc falls between v pfd (max) and v pfd (min) (see figure 17 on page 31 ). at this time, the reset pin (rst ) is driven active and will remain active until v cc returns to nominal levels. when v cc falls below the switchover voltage (v so ), power input is switched from the v cc pin to the snaphat battery (or external battery for so16) at this time, and the clock registers are maintained from the attached battery supply. all outputs become high impedance. on power-up, when v cc returns to a nominal value, write protection continues for t rec by internally inhibiting e . the rst signal also remains active during this time (see figure 17 on page 31 ). before the next active cycle, chip enable should be taken high for at least t ehel , then low. for a further more detailed review of battery lifetime calculations, please see application note an1012.
operation m41t94 16/41 figure 9. read mode sequence figure 10. write mode sequence scl sdi e sdo 2 high impedance w/r bit 7 bit address 0 msb data out msb msb (byte 1) data out (byte 2) 1 12 13 14 15 16 17 22 3 4 5 6 7 8 9 2 0 1 3 4 5 6 7 2 0 1 3 4 5 6 7 2 0 1 3 4 5 6 7 ai04635 scl sdi e sdo 7 2 high impedance 0 data byte 7 bit addr w/r bit 10 15 msb msb 6 6 5 5 4 4 3 3 21 1 0 65 4321 0 7 7 7 8 9 ai04636
m41t94 clock operations 17/41 4 clock operations the eight byte clock register (see table 4 on page 18 ) is used to both set the clock and to read the date and time from the clock, in a binary coded decimal format. tenths/hundredths of seconds, seconds, minutes, and hours are contained within the first four registers. bits d6 and d7 of clock register 03h (century/hours register) contain the century enable bit (ceb) and the century bit (cb). setting ceb to a '1' will cause cb to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). if ceb is set to a '0,' cb will not toggle. bits d0 throug h d2 of register 04h c ontain the day (day of week). registers 05h, 06h, and 07h contain the date (day of month), month and years. the ninth clock register is the control register (this is described in the clock calibration section). bit d7 of register 01h contains the stop bi t (st). setting this bit to a '1' will cause the oscillator to stop. if the device is expected to spend a significant amount of time on the shelf, the oscillator may be stopped to reduce current drain. when reset to a '0' the oscillator restarts within one second. the eight clock registers may be read one byte at a time, or in a sequential block. the control register (address location 08h) may be accessed independently. provision has been made to assure that a clock update does not occur while any of the eight clock addresses are being read. if a clock addr ess is being read, an update of the clock registers will be halted. this will prevent a transit ion of data during the read. 4.1 power-down time-stamp when a power failure occurs, the halt update bit (ht) will automatically be set to a '1.' this will prevent the clock from updating the clock registers, an d will allow the user to read the exact time of the power-down event. resetti ng the ht bit to a '0' will allow the clock to update the clock registers with the current time. for more information, see application note an1572. 4.2 clock registers the m41t94 offers 20 internal registers which contain clock, alarm, watchdog, flag, square wave and control data (see table 4 on page 18 ). these registers are memory locations which contain external (user accessible) and internal copies of the data (usually referred to as biport ? cells). the external copies are independent of internal functions except that they are updated periodically by the simultaneous transfer of the incremented internal copy. the internal divider (or clock) chain will be re set upon the completion of a write to any clock address. the system-to-user transfer of clock data w ill be halted whenever the clock addresses (00h to 07h) are being written. the update will resume either due to a deselect condition or when the pointer increments to a non-clock or ram address. clock and alarm registers store data in bcd. control, watchdog and square wave registers store data in binary format.
clock operations m41t94 18/41 table 4. clock register map (1) 1. keys: s = sign bit ft = frequency test bit st = stop bit 0 = must be set to zero bl = battery low flag (read only) bmb0-bmb4 = watchdog multiplier bits ceb = century enable bit cb = century bit out = output level afe = alarm flag enable flag rb0-rb1 = watchdog resolution bits wds = watchdog steering bit abe = alarm in battery back-up mode enable bit rpt1-rpt5 = alarm repeat mode bits wdf = watchdog flag (read only) wdf = watchdog flag (read only) af = alarm flag (read only) sqwe = square wave enable rs0-rs3 = sqw frequency ht = halt update bit tr = t rec bit addr function/range bcd format d7 d6 d5 d4 d3 d2 d1 d0 00h 0.1 seconds 0.01 seconds seconds 00-99 01h st 10 seconds seconds seconds 00-59 02h 0 10 minutes minutes minutes 00-59 03h ceb cb 10 hours hours (24 hour format) century/hours 0-1/00-23 04h tr 0 0 0 0 day of week day 01-7 05h 0 0 10 date date: day of month date 01-31 06h 0 0 0 10m month month 01-12 07h 10 years year year 00-99 08h out ft s calibration control 09h wds bmb4 bmb3 bmb2 bmb1 bmb0 rb1 rb0 watchdog 0ah afe sqwe abe al 10m alarm month al month 01-12 0bh rpt4 rpt5 ai 10 date alarm date al date 01-31 0ch rpt3 ht ai 10 hour alarm hour al hour 00-23 0dh rpt2 alarm 10 minutes alarm minutes al min 00-59 0eh rpt1 alarm 10 seconds alarm seconds al sec 00-59 0fhwdfaf0bl0000 flags 10h 0 0 0 0 0 0 0 0 reserved 11h 0 0 0 0 0 0 0 0 reserved 12h 0 0 0 0 0 0 0 0 reserved 13h rs3 rs2 rs1 rs0 0 0 0 0 sqw
m41t94 clock operations 19/41 4.3 setting alarm clock registers address locations 0ah-0eh contain the alarm settings. the alarm can be configured to go off at a prescribed time on a specific month, date, hour, minute, or second, or repeat every year, month, day, hour, minute, or second. it can also be programmed to go off while the m41t94 is in the battery backup to serve as a system wake-up call. bits rpt5-rpt1 put the alarm in the repeat mode of operation. table 5 on page 19 shows the possible configurations. codes not listed in the table default to the once per second mode to quickly alert the user of an incorrect alarm setting. when the clock information matches the alarm clock settings based on the match criteria defined by rpt5-rpt1, the af (alarm flag) is set. if afe (alarm flag enable) is also set, the alarm condition activates the irq /ft/out pin. note: i f the address pointer is allowed to increment to the flag register address, an alarm condition will not cause the interrupt/flag to occur until the address poin ter is moved to a different address. it should also be noted that if the last address written is the ?alarm seconds,? the address pointer will incr ement to the flag address, ca using this situation to occur. to disable the alarm, write '0' to the alarm date register and to rpt1?5. the irq /ft/out output is cleared by a read to the flags register. this read of the flags register will also reset the alarm flag (d6; register 0fh). see figure 11 on page 19 . the irq /ft/out pin can also be activated in the battery backup mode. the irq /ft/out will go low if an alarm occurs and both abe (ala rm in battery backup mode enable) and afe are set. the abe and afe bits are reset during power-up, th erefore an alarm generated during power-up will only set af. the user can read the flag register at system boot-up to determine if an alarm was generated while the m41t94 was in the deselect mode during power-up. figure 12 on page 20 illustrates the backup mode alarm timing. figure 11. alarm interrupt reset waveforms table 5. alarm repeat mode rpt5 rpt4 rpt3 rpt2 rpt1 alarm setting 1 1 1 1 1 once per second 1 1 1 1 0 once per minute 1 1 1 0 0 once per hour 1 1 0 0 0 once per day 1 0 0 0 0 once per month 0 0 0 0 0 once per year ai03664 irq/ft/out active flag 0fh 0eh 10h high-z
clock operations m41t94 20/41 figure 12. backup mode alarm waveforms ai03920 v cc irq/ft/out v pfd abe, afe bits in interrupt register af bit in flags register high-z v so high-z trec
m41t94 clock operations 21/41 4.4 watchdog timer the watchdog timer can be used to detect an out-of-control microprocessor. the user programs the watchdog timer by setting the desired amount of time-out into the watchdog register, address 09h. bits bmb4-bmb0 store a binary multiplier and the two lower order bits rb1-rb0 select the resolution, where 00 = 1 / 16 second, 01 = 1 / 4 second, 10 = 1 second, and 11 = 4 seconds. the amount of time-out is then determined to be the multiplication of the five-bit multiplier value with the resolution. (for example: writing 00001110 in the watchdog register = 3*1 or 3 seconds). note: accuracy of timer is wit hin the selected resolution. if the processor does not reset the timer within the specified period, the m41t94 sets the wdf (watchdog flag) and generates a watchdog interrupt or a microprocessor reset. wdf is reset by reading the flags register (0fh). the most significant bit of the watchdog register is the watchdog steering bit (wds). when set to a '0,' the watchdog will activate the irq /ft/out pin when timed-out. when wds is set to a '1,' the watchdog will output a negative pulse on the rst pin for t rec . the watchdog register and the afe, abe, sqwe, and ft bits will reset to a '0' at the end of a watchdog time-out when the wds bit is set to a '1.' the watchdog timer can be reset by two methods: 1. a transition (high-to-low or low-to-high) can be applied to the watchdog input pin (wdi), or 2. the microprocessor can perform a write of the watchdog register. the time-out period then starts over. the wdi pin should be tied to v ss if not used. in order to perform a software reset of the watchdog timer, the original time-out period can be written into the watchdog register, effectively restarting the count-down cycle. should the watchdog timer time-out, and the wds bit is programmed to output an interrupt, a value of 00h needs to be written to the watchdog register in order to clear the irq /ft/out pin. this will also disable the watchdog functi on until it is again programmed correctly. a read of the flags register will reset the watchdog flag (bit d7; register 0fh). the watchdog function is automatically disabled upon power-up and the watchdog register is cleared. if the watchdog function is set to output to the irq /ft/out pin and the frequency test (ft) function is activated, the watchdog function prevails and the frequency test function is denied. 4.5 square wave output the m41t94 offers the user a programmable square wave function which is output on the sqw pin. rs3-rs0 bits located in 13h establish the square wave output frequency. these frequencies are listed in table table 6 on page 22 . once the selection of the sqw frequency has been completed, the sqw pin can be turned on and off under software control with the square wave enable bit (sqwe) located in register 0ah.
clock operations m41t94 22/41 4.6 power-on reset the m41t94 continuously monitors v cc . when v cc falls to the power fail detect trip point, the rst pulls low (open drain) and remains low on power-up for t rec after v cc passes v pfd (max). the rst pin is an open drain output and an appropriate pull-up resistor should be chosen to control rise time. 4.7 reset inputs (rstin1 & rstin2 ) the m41t94 provides two independent inputs which can generate an output reset. the duration and function of these resets is iden tical to a reset generated by a power cycle. table 7 on page 23 and figure 13 on page 23 illustrate the ac reset characteristics of this function. pulses shorter than t rlrh1 and t rlrh2 will not generate a re set condition. rstin1 and rstin2 are each internally pulled up to v cc through a 100 k resistor. table 6. square wave output frequency square wave bits square wave rs3 rs2 rs1 rs0 frequency units 0000none? 000132.768khz 00108.192khz 00114.096khz 01002.048khz 01011.024khz 0110512hz 0111256hz 1000128hz 100164hz 101032hz 101116hz 11008hz 11014hz 11102hz 11111hz
m41t94 clock operations 23/41 figure 13. rstin1 and rstin2 timing waveforms 4.8 calibrating the clock the m41t94 is driven by a quartz-contro lled oscillator with a nominal frequency of 32,768 hz. uncalibrated clock accuracy will not exceed 35 ppm (parts per million) oscillator frequency erro r at 25c, which equates to about 1.53 minutes per month. when the calibration circuit is properly employed, accuracy improves to better than 2 ppm at 25c. the oscillation rate of crystals changes with temperature (see figure 14 on page 25 ). therefore, the m41t94 design employs periodic counter correction. the calibration circuit adds or subtracts counts from the oscillator divider circui t at the divide by 256 stage, as shown in figure 15 on page 25 . the number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five calibration bits found in the control register. adding counts speeds the clock up, subtracting counts slows the clock down. the calibration bits occupy the five lower order bits (d4-d0) in the control register (8h). these bits can be set to represent any value between 0 and 31 in binary form. bit d5 is a sign bit; '1' indicates positive calibration, '0' indicates negative calibration. calibration occurs within a 64 minute cycle. the first 62 minutes in the cycle may, once per minute, have one second either shortened by 1 28 or lengthened by 2 56 oscillator cycles. if a binary '1' is loaded into the register, only th e first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. table 7. reset ac characteristics (1) 1. valid for ambient operating temperature: t a = ?40 to 85c; v cc = 2.7 to 5.5 v (except where noted). symbol parameter min max unit t rlrh1 (2) 2. pulse width less than 50 ns will result in no reset (for noise immunity). rstin1 low to rstin1 high 200 ns t rlrh2 (3) 3. pulse width less than 20 ms will resu lt in no reset (for noise immunity). rstin2 low to rstin2 high 100 ms t r1hrh (4) 4. programmable (see table on page 27 ). rstin1 high to rst high 40 200 ms t r2hrh (4) rstin2 high to rst high 40 200 ms ai03665 rstin2 rst (1) rstin1 trlrh1 trlrh2 tr1hrh tr2hrh
clock operations m41t94 24/41 therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 ac tual oscillator cycles, that is +4.068 or ?2.034 ppm of adjustment per calibration step in the calibration register. as suming that the oscillator is running at exactly 32,768 hz, each of the 31 increments in the calibration byte would represent +10.7 or ?5.35 seconds per month which corresponds to a total range of +5.5 or ?2.75 minutes per month. two methods are available for ascertaining how much calibration a given m41t94 may require. the first involves setting the clock, letting it run for a month and comparing it to a known accurate reference and recording deviation over a fixed period of time. calibration values, including the number of seconds lost or gained in a given period, can be found in application note an934: timekeeper ? calibration. this allows the designer to give the end user the ability to calibrate the clock as the environm ent requires, even if the final product is packaged in a non-user serviceable enclosure. the designer could provide a simple utility that accesses the calibration byte. the second approach is better suited to a manufacturing environment, and involves the use of the irq /ft/out pin. the pin will toggle at 512 hz, when the stop bit (st, d7 of 1h) is '0,' the frequency test bit (ft, d6 of 8h) is '1,' the alarm flag enable bit (afe, d7 of ah) is '0,' and the watchdog steering bit (wds, d7 of 9h) is '1' or the watchdog register (9h = 0) is reset. any deviation from 512 hz indicates the degree and direction of oscilla tor frequency shift at the test temperature. for example, a reading of 512.010124 hz would indicate a +20 ppm oscillator frequency erro r, requiring a ?10 (xx001010) to be loaded into the ca libration byte for correction. note: setting or changing the calibration byte does not affect the frequency test output frequency. the irq /ft/out pin is an open drain output which requires a pull-up resistor for proper operation. a 500 to 10 k resistor is recommended in order to control the rise time. the ft bit is cleared on power-down.
m41t94 clock operations 25/41 figure 14. crystal accuracy across temperature figure 15. calibration waveform 4.9 century bit bits d7 and d6 of clock register 03h contain the century enable bit (ceb) and the century bit (cb). setting ceb to a '1' will cause cb to toggle, either from a '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). if ceb is set to a '0,' cb will not toggle. ai00999b ?160 0 10203040506070 frequency (ppm) temperature c 80 ?10 ?20 ?30 ?40 ?100 ?120 ?140 ?40 ?60 ?80 20 0 ?20 f = k x (t ?t o ) 2 k = ?0.036 ppm/ c 2 0.006 ppm/ c 2 t o = 25 c 5 c f ai00594b normal positive calibration negative calibration
clock operations m41t94 26/41 4.10 output driver pin when the ft bit, afe bit and watchdog register are not set, the irq /ft/out pin becomes an output driver that reflects the contents of d7 of the control register. in other words, when d7 (out bit) and d6 (ft bit) of address location 08h are a '0,' then the irq /ft/out pin will be driven low. note: the irq /ft/out pin is an open drain which requires an external pull-up resistor. 4.11 battery low warning the m41t94 automatically performs battery voltage monitoring upon power-up and at factory-programmed time intervals of approximately 24 hours. the battery low (bl) bit, bit d4 of flags register 0fh, will be asserted if the battery volt age is found to be less than approximately 2.5 v. the bl bit will remain asse rted until completion of battery replacement and subsequent battery low monitoring tests, either during the next power-up sequence or the next scheduled 24-hour interval. if a battery low is generated during a power-up sequence, this indicates that the battery is below approximately 2.5 volts and may not be able to maintain data integrity in the sram. data should be considered suspect and verified as correct. a fresh battery should be installed. if a battery low indication is generated during the 24-hour interval check, this indicates that the battery is near end of life. however, data is not compromised due to the fact that a nominal v cc is supplied. in order to insure data integrity during subsequent periods of battery backup mode, the battery should be replaced. the snaphat ? top may be replaced while v cc is applied to the device. note: this will cause the clock to lose time during the interval the snaphat ? battery/crystal top is disconnected. the m41t94 only monitors the battery when a nominal v cc is applied to the device. thus applications which require extensive durations in the battery backup mode should be powered-up periodically (at least once every few months) in order for this technique to be beneficial. additionally, if a battery low is indicated, data integrity should be verified upon power-up via a checksum or other technique. 4.12 t rec bit bit d7 of clock register 04h contains the t rec bit (tr). t rec refers to the automatic continuation of the deselect time after v cc reaches v pfd . this allows for a voltage setting time before writes may again be performed to the device after a power-down condition. the t rec bit will allow the user to set the length of this deselect time as defined by ta bl e 8 on page 27 .
m41t94 clock operations 27/41 4.13 initial power-on defaults upon initial application of power to the device, the following register bits are set to a '0' state: watchdog register, tr, ft, afe, abe, and sqwe . the following bits are set to a '1' state: st, out, and ht (see table 9: default values ). table 8. t rec definitions t rec bit (tr) stop bit (st) t rec time units min max 009698ms 0140200 (1) 1. default setting ms 1 x 50 2000 s table 9. default values condition tr st ht out ft afe abe sqwe watchdog register (1) 1. bmb0-bmb4, rb0, rb1. initial power-up (battery attach for snaphat ? ) (2) 2. state of other control bits undefined. 0111000 0 0 subsequent power-up (with battery backup) (3) 3. uc = unchanged uc uc 1 uc 0 0 0 0 0
maximum ratings m41t94 28/41 5 maximum ratings stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not imp lied. exposure to absolute ma ximum rating conditions for extended periods may affect device reliability. refer also to the stmicroelectronics sure program and other relevant quality documents. caution: negative undershoots below ?0.3 v are not allowed on any pin while in the battery backup mode. caution: do not wave solder soic to avoid damaging snaphat ? sockets. table 10. absolute maximum ratings symbol parameter value unit t stg storage temperature (v cc off, oscillator off) snaphat ? ?40 to 85 c soic ?55 to 125 c v cc supply voltage ?0.3 to 7 v t sld (1) 1. for so16 and soh28 package, lead-free (pb-free) lead finish: reflow at peak temperature of 260c (the time above 255c must not exceed 30 seconds). lead solder temperature for 10 seconds 260 c v io input or output voltage ?0.3 to v cc +0.3 v i o output current 20 ma p d power dissipation 1 w
m41t94 dc and ac parameters 29/41 6 dc and ac parameters this section summarizes the operating and measurement conditions, as well as the dc and ac characteristics of the device. the parameters in the following dc and ac characteristic tables are derived from tests performed under the measurement conditions listed in the relevant tables. designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. figure 16. ac testing input/output waveforms table 11. dc and ac measurement conditions (1) 1. output hi-z is defined as the point where data is no longer driven. parameter m41t94 v cc supply voltage 2.7 to 5.5 v ambient operating temperature ?40 to 85c load capacitance (c l ) 100 pf input rise and fall times 50 ns input pulse voltages 0.2 to 0.8v cc input and output timing ref. voltages 0.3 to 0.7v cc table 12. capacitance symbol parameter (1)(2) 1. effective capacitance m easured with power supply at 5 v; sampled only, not 100% tested. 2. at 25c, f = 1 mhz. min max unit c in input capacitance 7 pf c out (3) 3. outputs are deselected. output capacitance 10 pf t lp low-pass filter input time constant (sda and scl) 50 ns ai02568 0.8v cc 0.2v cc 0.7v cc 0.3v cc
dc and ac parameters m41t94 30/41 table 13. dc characteristics symb. parameter test condition (1) min typ max unit i bat battery current osc on t a = 25c, v cc = 0 v, v bat = 3 v 400 500 na battery current osc off 50 na i cc1 supply current f = 2 mhz 2 ma i cc2 supply current (standby) scl, sdi = v cc ? 0.3 v 1.4 ma i li (2) input leakage current 0 v v in v cc 1 a i lo (3) output leakage current 0 v v out v cc 1 a v ih input high voltage 0.7v cc v cc + 0.3 v v il input low voltage ?0.3 0.3v cc v v bat battery voltage 2.5 3.5 (4) v v oh output high voltage (5) i oh = ?1.0 ma 2.4 v v ol output low voltage (5) i ol = 3.0 ma 0.4 v output low voltage (open drain) (6) i ol = 10 ma 0.4 pull-up supply voltage (open drain) rst , irq /ft/out 5.5 v v pfd power fail deselect (ths = v cc ) 4.20 4.40 4.50 v power fail deselect (ths = v ss ) 2.55 2.60 2.70 v so battery backup switchover 2.5 v 1. valid for ambient operating temperature: t a = ?40 to 85c; v cc = 2.7 to 5.5 v (except where noted). 2. rstin1 and rstin2 internally pulled up to v cc through 100 k resistor. wdi internally pulled-down to v ss through 100 k resistor. 3. outputs deselected. 4. for rechargeable back-up, v bat (max) may be considered v cc . 5. for sqw pin (cmos). 6. for irq /ft/out, rst pins (open drain): if pull ed up to supply other than v cc , this supply must be equal to, or less than 3.0 v when v cc = 0 v (during battery backup mode). table 14. crystal electrical characteristics (externally supplied) symbol parameter (1)(2) typ min max unit f 0 resonant frequency 32.768 khz r s series resistance 50 k c l load capacitance 12.5 pf 1. load capacitors are integrated within the m41t94. circuit boar d layout considerations for the 32.768 khz crystal of minimum trace lengths and isolation from rf generating signals should be taken into account. these characteristics are externally supplied. 2. stmicroelectronics recommends the kds dt-38: 1ta/1t c252e127, tuning fork type (t hru-hole) or the dmx-26s: 1tjs125fh2a212, (smd) quartz crystal for i ndustrial temperature operations. for contac t information on this crystal type, see section 10: references on page 39 .
m41t94 dc and ac parameters 31/41 figure 17. power down/up mode ac waveforms table 15. power down/up ac characteristics symbol parameter (1) 1. valid for ambient operating temperature: t a = ?40 to 85c; v cc = 2.7 to 5.5 v (except where noted). min typ max unit t f (2) 2. v pfd (max) to v pfd (min) fall time of less than t f may result in deselection/write protection not occurring until 200 s after v cc passes v pfd (min). v pfd (max) to v pfd (min) v cc fall time 300 s t fb (3) 3. v pfd (min) to v ss fall time of less than t fb may cause corruption of ram data. v pfd (min) to v ss v cc fall time 10 s t r v pfd (min) to v pfd (max) v cc rise time 10 s t rb v ss to v pfd (min) v cc rise time 1 s t rec (4) 4. programmable (see table 8 on page 27 ). power up deselect time 40 200 ms t dr expected data retention time 10 (5) 5. at 25c, v cc = 0 v (when using soh28 + m4t28-br12sh snaphat ? top). years ai03687 v cc inputs (per control input) outputs don't care high-z tf tfb tr trb tdr valid valid (per control input) recognized recognized v pfd (max) v pfd (min) v so trec rst
package mechanical data m41t94 32/41 7 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark.
m41t94 package mechanical data 33/41 figure 18. so16 ? 16-lead plastic small outline package outline note: drawing is not to scale. so-b e n cp b e a2 d c l a1 h a 1 table 16. so16 ? 16-lead plastic small outline package mechanical data symbol millimeters inches typ min max typ min max a 1.75 0.069 a1 0.10 0.25 0.004 0.010 a2 1.60 0.063 0 8 0 8 b 0.35 0.46 0.014 0.018 c 0.19 0.25 0.007 0.010 cp 0.10 0.004 d 9.80 10.00 0.386 0.394 e1.27??0.050? ? e 3.80 4.00 0.150 0.157 l 0.40 1.27 0.016 0.050 n16 16
package mechanical data m41t94 34/41 figure 19. soh28 ? 28-lead plastic small outline, battery snaphat ? , package outline note: drawing is not to scale. soh-a e n d c l a1 1 h a cp be a2 eb table 17. soh28 ? 28-lead plastic small outline, battery snaphat ? , package mechanical data symbol millimeters inches typ min max typ min max a??3.05??0.120 a1 ? 0.05 0.36 ? 0.002 0.014 a2 ? 2.34 2.69 ? 0.092 0.106 b ? 0.36 0.51 ? 0.014 0.020 c ? 0.15 0.32 ? 0.006 0.012 d ? 17.71 18.49 ? 0.697 0.728 e ? 8.23 8.89 ? 0.324 0.350 e1.27? ?0.050? ? eb ? 3.20 3.61 ? 0.126 0.142 h ? 11.51 12.70 ? 0.453 0.500 l ? 0.41 1.27 ? 0.016 0.050 ? 0 8 ? 0 8 n28 28 cp ? ? 0.10 ? ? 0.004
m41t94 package mechanical data 35/41 figure 20. sh ? 4-pin snaphat ? housing for 48 mah battery & crystal, package outline note: drawing is not to scale. shtk-a a1 a d e ea eb a2 b l a3 table 18. sh ? 4-pin snaphat ? housing for 48 mah battery & crystal, package mechanical data symbol millimeters inches typ min max typ min max a??9.78??0.385 a1 ? 6.73 7.24 ? 0.265 0.285 a2 ? 6.48 6.99 ? 0.255 0.275 a3 ? ? 0.38 ? ? 0.015 b ? 0.46 0.56 ? 0.018 0.022 d ? 21.21 21.84 ? 0.835 0.8560 e ? 14.22 14.99 ? 0.556 0.590 ea ? 15.55 15.95 ? 0.612 0.628 eb ? 3.20 3.61 ? 0.126 0.142 l ? 2.03 2.29 ? 0.080 0.090
package mechanical data m41t94 36/41 figure 21. sh ? 4-pin snaphat ? housing for 120 mah battery & crystal, package outline note: drawing is not to scale. shtk-a a1 a d e ea eb a2 b l a3 table 19. sh ? 4-pin snaphat ? housing for 120 mah battery & crystal, package mech. data symbol millimeters inches typ min max typ min max a ? ? 10.54 ? ? 0.415 a1 ? 8.00 8.51 ? 0.315 0.335 a2 ? 7.24 8.00 ? 0.285 0.315 a3 ? ? 0.38 ? ? 0.015 b ? 0.46 0.56 ? 0.018 0.022 d ? 21.21 21.84 ? 0.835 0.860 e ? 17.27 18.03 ? 0.680 0.710 ea ? 15.55 15.95 ? 0.612 0.628 eb ? 3.20 3.61 ? 0.126 0.142 l ? 2.03 2.29 ? 0.080 0.090
m41t94 part numbering 37/41 8 part numbering table 20. ordering information scheme caution: do not place the snaphat ? battery package ?m4txx-br12sh? in conductive foam as it will drain the lithium button-cell battery. for other options, or for more information on any aspect of this device, please contact the st sales office nearest you. example: m41t 94 mh 6 e device type m41t supply voltage and write protect voltage 94 = v cc = 2.7 to 5.5 v ths = v cc ; 4.20 v v pfd 4.50 v ths = v ss ; 2.55 v v pfd 2.70 v package mq = so16 mh (1) = soh28 1. the 28-pin soic package (soh28) requires the snaphat ? battery/crystal package which is ordered separately under the part number ?m4txx-br12shx? in plastic tube or ?m4txx-br12shxtr? in tape & reel form (see table table 21 on page 37 ). temperature range 6 = ?40 to 85c shipping method e = lead-free package (ecopack ? ), tubes f = lead-free package (ecopack ? ), tape & reel table 21. snaphat ? battery table part number description package M4T28-BR12SH1 lithium battery (48 mah) and crystal snaphat ? sh m4t32-br12shx lithium battery (120 mah) and crystal snaphat ? sh
environmental information m41t94 38/41 9 environmental information figure 22. recycling symbols this product contains a non-rechargeable lithi um (lithium carbon monofluoride chemistry) button cell battery fully encapsulated in the final product. recycle or dispose of batteries in accordance with the battery manufacturer's instructions and local/national disposal and recycling regulations. please refer to the following web site address for additional information regarding compliance statements and waste recycling. go to www.st.com/rtc , then select "lithium battery recycling" from "related topics".
m41t94 references 39/41 10 references the crystal supplier kds as cited in table 14: crystal electrical characteristics (externally supplied) on page 30 can be contacted at kouhou@kdsj.co.jp or http://xxx.kdsj.co.jp .
revision history m41t94 40/41 11 revision history table 22. document revision history date revision changes apr-2002 1 first edition 25-apr-2002 1.1 adjust graphic ( figure 4 on page 9 ); fix table text ( table 10 on page 28 , table 20 on page 37 ); adjust characteristics ( table 13 on page 30 , table 14 on page 30 ) 03-jul-2002 1.2 modify dc, crystal electrical characteristics footnotes, default value table ( table 13 on page 30 , table 14 on page 30 , table 9 on page 27 ) 06-nov-2002 1.3 correct dimensions ( table 19 on page 36 ) 26-mar-2003 1.4 update test condition ( table 15 on page 31 ) 28-apr-2003 2 new si changes ( figure 4 on page 9 ; table 15 on page 31 , ta bl e 7 o n page 23 , table 8 on page 27 , table 9 on page 27 ) 15-jun-2004 3 reformatted; added lead-free information; update characteristics ( figure 14 on page 25 ; table 10 on page 28 , table 13 on page 30 , table 20 on page 37 ) 29-aug-2006 4 changed document to new template; amalgamated diagrams in features on page 1 ; updated package mechanical data in section 7: package mechanical data ; small text changes for entire document, ecopack compliant 09-nov-2007 5 added lead-free second level interconnect information to cover page and section 7: package mechanical data ; minor formatting changes throughout document; updated ta b l e 1 0 , footnote 1 in ta b l e 1 4 , ta bl e 2 0 , 21 ; addition of section 10: references . 13-jan-2009 6 updated ta b l e 1 0 ; updated text in section 7: package mechanical data ; added section 9: environmental information .
m41t94 41/41 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2009 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of M4T28-BR12SH1

	To Download M4T28-BR12SH1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .